We understand the challenges you face, the importance of reliability, and the relationship between uptime and productivity. That’s why we continually strive to produce the safest, most reliable and productive hydraulic mining shovels possible. Offering the widest payload range of any manufacturer in the industry, the ability to optimally pair with our popular line of mining trucks, and the support of our world-class Cat dealer network, we are uniquely positioned to partner with you to help achieve your productivity targets. We understand what matters to you. Our hydraulic mining shovels are built with you in mind. Because in mining, every day matters and every load counts.
General
- Engine Output - SAE J1995
- 2996 HP
- Bucket Payload
- 67.5 ton (US)
- Operating Weight
- 650.4 ton (US)
- Note
- Specifications shown above apply to Face Shovel configuration. Backhoe and Frontless configurations are also available.
Hydraulic System with Pump Managing System
- Maximum Pressure - Attachment
- 4640 psi
- Maximum Pressure - Swing Pumps
- 5365 psi
- Maximum Pressure - Travel
- 5365 psi
- Features (1)
- Pressure cut-off for main pumps
- Features (2)
- Cooling of pump transmission gear oil
- Filters
- – Full-flow high-pressure filters (100 μm) for the main pumps, installed directly behind each pump
– High pressure filters (200 μm) for the closed swing circuit
– Full-flow filters (10 μm) for the complete return circuit
– Pressure filters (40 μm - Hydraulic Tank Capacity - Approximately
- 1876 gal (US)
- Main Pumps
- 4 Ă— swash plate double pumps
- Maximum Oil Flow - Main Pumps
- 4 Ă— 1300 L/min (4 Ă— 343 gal/min)
- Maximum Oil Flow - Swing Pumps
- 4 Ă— 352 L/min (4 Ă— 93 gal/min)
- Pump Managing System contains:
- – Electronic load limit control
– Flow on demand from main pumps depending on joystick position
– Automatic regulation of main pumps to zero flow without demand
– Automatic rpm reduction of engine speed during working breaks
– Reduced oil flow - Swing Pumps
- 4 Ă— reversible swash plate pumps
- Total Volume of Hydraulic Oil - Approximately
- 1930 gal (US)
Hydraulic Oil Cooling
- Components
- Gear-type cooling pumps supplying high-volume, low-pressure oil to fans and aluminum coolers
- Diameter - Fan
- 4 Ă— 1170 mm (4 Ă— 46 in)
- Features (1)
- Cooling system fully independent of all main circuits, i.e. controlled cooling capacity is available whenever engine is running
- Features (2)
- Fan speed and flow of oil to the coolers are thermostatically controlled
- Features (3)
- Extremely high cooling efficiency to ensure optimum oil temperature
- Oil Flow of Cooling Pumps
- 4 Ă— 488 L/min (4 Ă— 129 gal/min)
Operator's Cab
- Components (1)
- Pneumatically cushioned and multi-adjustable comfort seat with lumbar support, safety belt, head and armrests
- Components (11)
- Sliding emergency ladder (kick-down type) with ladder cage
- Components (12)
- Machine access via retractable access stairway, stairway angle approximately 45°, hydraulically operated
- Components (13)
- Roller blinds at all windows
- Components (2)
- Under roof mounted heating ventilating and air conditioning system
- Components (3)
- Windshield with parallel intermittent wiper/washer
- Components (4)
- All-round safety glass, armored windshield and sliding side window
- Components (5)
- Operator Protective Guard (Top Guard approved according to ISO 10262:1998)
- Components (6)
- Fold-away auxiliary seat with safety belt
- Components (7)
- External sun shields at side and rear windows
- Components (8)
- Switch in seat cushion to automatically neutralize the hydraulic controls when operator leaves the seat
- Components (9)
- Joystick controls integrated in independently adjustable seat consoles
- Internal Dimensions of Cab - Height
- 7.05 ft
- Internal Dimensions of Cab - Length
- 7.22 ft
- Internal Dimensions of Cab - Width
- 5.25 ft
- Operator's Eye Level - Approximately
- 24.93 ft
- Board Control System (BCS III)
- Electronic monitoring, data logging and diagnostic system for vital signs and service data of engines, hydraulic system and lubrication system, featuring:
– Robust instrument panel including large (12 in) colored touch screen for intuitive handling
Swing System
- Features (1)
- Dirt wipers at swing ring to prevent build-up of debris between swing ring and carbody
- Features (2)
- Closed-loop swing circuit with torque control
- Features (3)
- Hydraulic braking of the swing motion by counteracting control
- Features (4)
- All raceways and the internal gearing of swing ring, supplied by automatic central lubrication system
- Maximum Swing Speed
- 3.8 r/min
- Parking Brakes
- Wet multiple disc brake, spring loaded/hydraulically released
- Swing Drive
- 4 compact planetary transmissions with axial piston motors
- Swing Ring
- Triple-race roller bearing with sealed internal gearing
Undercarriage
- Bottom Rollers - Each Side
- 7
- Components (1)
- All running surfaces of sprockets, idlers, rollers & pad links, as well as teeth contact areas of sprocket & pad links, are hardened
- Components (2)
- Acoustic travel alarm
- Components (3)
- Cast double-grouser combined pad links with bushings connected by hardened full floating pins
- Components (4)
- Bottom rollers are connected to the automatic lubrication system
- Components (5)
- Fully hydraulic, self-adjusting track tensioning system with piston accumulator
- Components (6)
- Automatic hydraulic retarder valve to prevent over-speed on downhill travel
- Gradeability - Travel Drives - Maximum
- 43 %
- Maximum Tractive Force
- 661160 lb
- Parking Brakes
- Wet multiple-disc brake, spring applied/hydraulically released
- Support Rollers - Each Side
- 2 plus a skid plate in between
- Track Pads - Each Side
- 42
- Travel Drives - Each Side
- 1 planetary transmission with 2 two-stage axial piston motors
- Travel Speed - 1st Stage - Maximum
- 0.68 mile/h
- Travel Speed - 2nd Stage - Maximum
- 0.99 mile/h
Automatic Lubrication System
- Capacity - Grease Container
- 264 gal (US)
- Type (1)
- Dual-circuit system with hydraulically driven heavy-duty pumps and electronic time relay control to adjust the pause/lube times
- Type (2)
- System failures displayed by Board Control System
- Type (3)
- Grease filters (200 μm) between service station and container as well as directly behind grease pump
- Type (4)
- Connected to main lube system are:
– pivot points of attachment, bucket and cylinders
– bottom rollers of undercarriage - Type (5)
- Connected to main lube system are:
– raceways of swing roller bearing
– 2 greasing pinions for the internal gearing of swing ring
Operating Weights
- 6060 - Ground Pressure
- 26.3 N/cm² (38.1 psi)
- 6060 - Operating Weight
- 1298510 lb
- 6060 - Standard Track Pads
- 4.59 ft
- 6060 FS - Ground Pressure
- 26.4 N/cm² (38.3 psi)
- 6060 FS - Operating Weight
- 1300710 lb
- 6060 FS - Standard Track Pads
- 4.59 ft
- Note
- Other track pads available on request.
Retractable Service Station
- Installation
- Retractable service station installed underneath the engine module and easily accessible from ground.
- Equipped With (1)
- Quick couplings for:
– Diesel fuel
– Engine coolant – left/right
– Pump transmission gear oil – left/right
– Engine oil – left/right
– Hydraulic oil tank
– Grease container - Equipped With (2)
- Cat jump-start socket
- Equipped With (3)
- Indicator lights for fuel tanks left/right full and grease container full
Attachments
- All buckets (FS and BH) are equipped with a wear package consisting of: (2)
- – Wing shrouds on side walls
– Heel shrouds at bottom edges - Type (8)
- Special wear packages for highly abrasive materials on request
- All buckets (FS and BH) are equipped with a wear package consisting of: (1)
- – Special liner material covering main wear areas inside and outside of bucket
– Lip shrouds between teeth - Shovel attachment with unique TriPower kinematics ensuring the following main features: (1)
- – Automatic roll-back limiter to prevent material spillage
– Kinematic assistance to hydraulic forces - Shovel attachment with unique TriPower kinematics ensuring the following main features: (2)
- – Horizontal Automatic constant-angle bucket guidance
– Vertical Automatic constant-angle bucket guidance - Shovel attachment with unique TriPower kinematics ensuring the following main features: (3)
- – Constant boom momentum throughout the entire lift arc
– Crowd force assistance - Type (1)
- Catwalks with rails at booms
- Type (2)
- Guards for shovel cylinders (FS)
- Type (3)
- Pressure-free lowering of boom (FS and BH) and stick (FS) by means of a float valve
- Type (4)
- Inspection holes in booms (FS and BH) and stick (FS)
- Type (5)
- Welding procedures allow for internal counter-welding (double prep weld) wherever possible
- Type (6)
- Booms and sticks are stress-relieved after welding
- Type (7)
- Booms and sticks are torsion-resistant, welded box design of high-tensile steel with massive steel castings at pivot areas
Diesel Engines
- Alternators
- 2 Ă— 150 A
- Aspiration
- Turbocharged and charge air-cooled
- Bore
- 6.69 in
- Components (1)
- Additional high-capacity water separator
- Components (2)
- Two-stage fuel filter including water separator
- Components (3)
- Heavy-duty air filters
- Components (4)
- Microprocessed engine management
- Components (5)
- Hydraulically driven radiator fan with electronically controlled fan speed
- Displacement
- 3574 in³
- Emissions
- Emit equivalent to U.S. EPA Tier 2
- Fuel Tank Capacity
- 3435 gal (US)
- Make/Model
- 2 Ă— Cat 3512C
- Number of Cylinders - Each Engine
- 12
- Stroke
- 8.46 in
- Gross Power - SAE J1995
- 2996 HP
- Maximum Altitude without Deration
- 3500 m (11,500 ft) – above sea level
- Net Power - ISO 9249
- 2968 HP
- Net Power - SAE J1349
- 2960 HP
- Rated Speed
- 1,800 min-1 (1,800 rpm)
Engine
- Engine Model
- 2 × Cat® 3512C
- Gross Power - SAE J1995
- 2996 HP
- Net Power - SAE J1349
- 2960 HP
Bucket
- Bucket Capacity - Backhoe (heaped 1:1)
- 44.5 yd³
- Bucket Capacity - Face Shovel (heaped 2:1)
- 44.5 yd³
Operating Specifications
- Bucket Payload
- 67 ton (US)
- Operating Weight - Backhoe
- 649 ton (US)
- Operating Weight - Face Shovel
- 650 ton (US)
Electrical System
- Batteries in Series/Parallel Installation
- 6 × 210 Ah – 12V each; 630 Ah – 24V in total
- Components (1)
- Battery isolation relays and switches
- Components (2)
- Emergency stop switches accessible from ground level and in engine module
- Components (3)
- 12 LED high-brightness working flood lights
– 10 for working area
– 2 for rear end - Components (4)
- 2 LED high-brightness access flood lights
- Components (5)
- 16 LED service lights
- System Voltage
- 24V
Features
- Feature (1)
- TriPower shovel attachment
- Feature (10)
- LED working lights
- Feature (2)
- Independent oil-cooling system
- Feature (3)
- Spacious walk-through machine house
- Feature (4)
- 5-circuit hydraulic system
- Feature (5)
- On-board electronics system: Control and Monitoring Platform (CAMP)
- Feature (6)
- Board Control System (BCS)
- Feature (7)
- Operator Assist (OA)
- Feature (8)
- Torque control in closed-loop swing circuit
- Feature (9)
- Automatic central lubrication system
